5
Mar

beckwood_387

Beckwood Slab-Side Press Example

In lieu of traditional two-post hydraulic presses, which feature two housing posts & are optimal designs for shallow-bed applications, slab-side designs are often the smarter frame configuration.

In a slab-side design, two solid plates of steel are used in place of the posts. This change from post to slab-sides increases the ease of assembly & can result in a net decrease in price of the press. Also, this substitution often allows for the use of less expensive, non-lubricated guide bushings on those presses which feature guided rams.

While the slab-side configuration is most often used on smaller, low tonnage systems, it has also been implemented successfully on larger units well in excess of 200 tons.  Finally, the lighter, compact design of a slab-side press lends itself well to applications featuring small heated platens for use in laboratory-type environments.

Category : Blog | Heated Platen | Hydraulic Press | Blog
8
Jan

For presses featuring light curtain safety guards, it is important that a stop-time analysis be performed in order to determine the appropriate distance the light curtains are placed relative to the press opening.

In order to determine this distance, Stopping & Speed Analyzers can be used. These devices take into consideration standard body speeds which have been researched and recorded. Trained safety operators then utilize the stop-time analysis results, coupled with the known ram speed information for the particular press in order to establish the safe mounting distance which the curtain must be placed to allow for moving operator limbs, etc.

Requesting that this procedure be performed by your hydraulic press manufacturer or safety specialists will ensure your investment in safety guarding is fully employed.

Category : Blog | Hydraulic Press | Hydraulic Press Controls | Press Safety | Blog
1
Dec

In an attempt to decrease margins and increased competition, today’s manufacturers are driven to consolidate processes, minimize operator error and reduce material scrap. In order to thrive in these conditions, manufacturers must push for a greater emphasis on technology. The hydraulic press market has grown with these challenging demands. One of the most popular advances is the utilization of Active Leveling Control (ALC). This technology counteracts the negative effects of off-center loading, significant breakthrough shock with high strength steels and reverse shock associated with the use of nitrogen in dies.

Active Leveling Control (ALC) is a technologically advanced system that utilizes closed loop control for each corner of the press ram, keeping the press ram in parallel and reducing any existing shock. Presses equipped with ALC utilize a high-speed motion controller, linear transducers and proportional valves to synchronize the press actuators. The 32-bit multi-axis high-speed motion controller provides less than 1 msec control loop time.

Active Leveling Control for bed-to-ram parallelism is offered in either 2 or 4 axis depending on the application. Two-axis control provides either left-to-right or front-to-rear parallelism. For users requiring both left-to-right and front-to-rear parallelism, four-axis control is recommended.

Off-Center loading can be caused by many issues and can cause unwanted symptoms to arise within the press, dies and overall application. Poor part quality & inconsistency, premature tool wear, and detrimental stress on the press structure are all likely to occur if the press has not been properly designed to handle an unbalanced load.

The most common cause of off-center loading is due to the geometry of the part formed not being conducive to an even load. Many applications do not form evenly over the press bed and can wreak havoc on a press or tooling. Other difficult Off-Center Loading processes many include progressive dies and the desire to consolidate multiple operations (and multiple dies) into a single machine. In addition, many presses can be improperly loaded due to operator error, creating additional alignment problems. This can especially be a problem for presses with big beds and/or small tooling.

A properly engineered Active Leveling Control system will provide many capabilities to counteract the negative effects of off-center loading. This improvement supplies protection for the press structure and tooling while decreasing maintenance costs. Many processes that historically could not be unified in one press are now being efficiently combined and properly executed with the integration of the ALC system. This feature enables companies to displace multiple presses and save valuable floor space, which in turn reduces labor costs and creates room for more capacity. The ALC technology is paralleled by servo mechanical presses but offers more flexibility at a significantly reduced price.

As hydraulic design technology advances, manufacturers will be presented with new capabilities to increase the efficiency of their production processes. Active Leveling Control can be integrated into a new hydraulic press to increase part quality, reduced die wear, and reduce complex setup time. This system provides the ideal solution for manufacturers who need to counteract the effects off-center loading, significant breakthrough shock, and reverse shock loading situations.

Category : Blog | Hydraulic Press | Hydraulic Press Controls | Hydraulic Press Economy | Hydraulic Press maintenance | Blog